白沙附近有没有服务

Jinan Ludao CNC Equipment Co., Ltd Specializing in the production of various CNC engraving machines, CNC cutting machines, laser metal cutting machines Wood carving machine

Service hotline Manager Zhang: 15588891951
Manager Zhang: 13075377501
Manager ran: 18668993808

Lu Diao hot search key words: Wood carving machine Stone carving machine Three process woodworking engraving machine Jade carving 3D scanner

Current location: home page » Engraving machine information » Q & A of engraving machine

Wood engraving machine related parameters set to extend life

Article source: our website publishing time: January 3, 2017 16:27:00, hits: 8028【 large in Small
The parameters of stepper motor in computer woodworking engraving machine are related to the speed and precision of engraving machine. Generally, the subdivision of stepping driver is set. Generally, the higher the subdivision, the higher the control resolution. However, if the fineness is too high, the maximum feed rate will be affected. For mould machine users, the pulse equivalent can be 0.001mm/p (at this time the maximum feed rate is 9600 mm / min) or 0.0005mm/p (at this time the maximum feed speed is 4800 mm / min); for users with low accuracy requirements of woodworking engraving machine, the pulse equivalent can be set larger, such as 0.002mm/p (the maximum feed speed is 19200 mm / min) or 0.005mm/p (the maximum feed speed is 48000 mm / min) mm/min)。 For two-phase stepping motor, the calculation method of pulse equivalent is as follows: pulse equivalent = lead screw pitch △ fraction △ 200.
Take off speed setting: this parameter corresponds to the take-off frequency of stepping motor. The so-called take-off frequency is the highest frequency that the stepper motor can start directly without acceleration. Reasonable selection of this parameter can improve the machining efficiency and avoid the low-speed section of the stepper motor with poor motion characteristics; however, if the parameter is selected too large, it will cause the car to be jammed, so we must leave some margin. In the motor factory parameters, generally including the take-off frequency parameters. However, after the woodworking engraving machine is assembled, the value may change, which generally needs to decrease, especially when carrying load. Therefore, the setting parameters should be determined by actual measurement after referring to the factory parameters of the motor.
Only setting the relevant parameters of woodworking engraving machine, and then producing according to the operation process, can not only improve the processing efficiency, but also maintain the service life of the engraving machine.

Lu Diao's latest products

Ordinary full automatic trimming and edge banding machine
 Ordinary full automatic trimming and edge banding machine
Edge sealing is an important process in panel furniture manufacturing. Edge sealing quality directly affects the quality, price and grade of products. Through edge sealing, the appearance quality of furniture is improved, and the damage of edges and corners, lifting or peeling of veneer layer are avoided in the process of transportation and use
Standard automatic double trimming edge banding machine
 Standard automatic double trimming edge banding machine
Specific functions: preheating, gluing, edging, pressing, cutting, front and back trimming, rough trimming, finishing, scraping and polishing. Weight: 1300kg edge banding thickness: 0.4-3mm minimum length of workpiece: 80mm; workpiece conveying speed: 18m / min; air pressure: 0.6mpa-0.8mpa rubber box
Ld4040 cylinder plane integrated metal engraving machine
 Ld4040 cylinder plane integrated metal engraving machine
Ld4040 metal engraving machine performance characteristics: metal engraving machine has become a metal mold machine, small mold machine, etc. 1. The bed is made of cast iron and the gantry column is made of cast iron. The machine is stable. 2. The guide rail adopts imported linear square gauge and three axis precision lead screw drive
Ld6060 metal engraving machine
 Ld6060 metal engraving machine
Ld4040 metal engraving machine performance characteristics: metal engraving machine has become a metal mold machine, small mold machine, etc. 1. The bed is made of cast iron and the gantry column is made of cast iron. The machine is stable. 2. The guide rail adopts imported linear square gauge and three axis precision lead screw drive
Ld325 row tool machining center
 Ld325 row tool machining center
CNC tool arranging machining center adopts 1 9kw tool changing spindle and 12 row tool changing tool storehouse; it can meet the requirements of various plate processing and engraving of various complex door panels; it can realize multi-purpose and high cost performance. The loading and unloading device can be further improved
Automatic loading and unloading of ld1324 process cutting machine
 Automatic loading and unloading of ld1324 process cutting machine
CNC cutting machine is a kind of special machine used for panel customized furniture CNC punching and slotting. It can get rid of the dependence of traditional cutting mode on manual work, and complete the vertical hole at the same time. Through the design of disassembly and typesetting software, intelligent production can be realized. Ld132sigong
Ld1315 cylinder plane integrated heavy stone engraving machine
 Ld1315 cylinder plane integrated heavy stone engraving machine
Stone engraving machine, three-dimensional stone engraving machine, three-dimensional engraving machine. 1. The bed is thick and generous
Automatic high and low pressure vacuum laminating machine
 Automatic high and low pressure vacuum laminating machine
Unique technology and configuration patent a three sets of heating system, secondary heating technology. The secondary heating system is a set of heating system independent of the original heating system. It can be opened for several seconds after the adsorption of PVC membrane is completed

Ranking of similar articles

Latest news articles